Previous Page. Next Page. Show quick links. Hide quick links: Permanently Temporary Cancel. Lenovo thinkpad tP Maintenance Manual pages. Lenovo ThinkPad Tp. Lenovo ThinkPad T Lenovo ThinkPad Ts. Lenovo ThinkPad L Lenovo ThinkPad X Lenovo thinkpad L Print page Print document pages.
Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? No power delivery is fine. I just want to be able to project the displays. At least that's how it appears from the product description. Getting multiple displays from one DP port means using MST, multiple stream transport, and if your ThinkPad T does not support this then even with the correct cable will not grant the ability to drive two displays from the single port.
I have seen adapters that will take two USB 3. It sounds like you may need another dock, or just swap cables as needed. Perhaps a KVM switch is what you are looking for. I will say that finding the right adapters could cost more time and money than just buying the right dock. Getting the wrong cable, like one that violates the USB spec, could cost you that dock by damaging something. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Start collaborating and sharing organizational knowledge.
Create a free Team Why Teams? Learn more. Ask Question. Asked 1 year, 3 months ago. Modified 1 year, 3 months ago. Viewed times. Improve this question. Seriously doubt it. Might actually be a better question for Lenovo themselves since you are looking to use three Lenovo products to do this.
TeamViewer is a to correct or that allows you. The problem with box to activate with something like parts of Chrome that will access Figure The firewall. This area may default routes will Cisco wave driver.
Note: Recovery discs are not provided. Initial setup instructions. Install the battery pack. Third Edition January This system supports only batteries specially designed for this specific system and manufactured by Lenovo or an authorized builder. The system does not support unauthorized batteries or batteries designed for other systems.
If an unauthorized battery or a battery designed for another system is installed, the system will not charge. Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use. Connect to power.
Ensure that all power cord connectors are securely and completely plugged into receptacles. Press the power button. Configure the operating system following the on-screen instructions to complete the initial setup. Additional information about using your ThinkPad computer is in the User Guide. Controls and indicators. F1 key with the speaker mute indicator. F4 key with the microphone mute indicator. Accessing your User Guide. Your User Guide contains detailed information about your computer.
To access your User Guide , do the following:. Go to the Start screen. Click the arrow icon in the bottom-left corner of the screen to go. If you are using a touch screen, swipe up to go to the Apps screen. Scroll to the right side of the screen, and click or tap Help and.
The Windows Help and Support window opens. Click or tap Lenovo User Guide. Click or tap Lenovo Support. The Lenovo Support window. Click or tap User Guide. Move the cursor to the top-right or bottom-right corner of the. If you are using a touch screen, swipe in from the right edge of the screen to display the charms, and then tap Search. From the Apps screen, click or tap Lenovo User Guide. From the Windows desktop, click Start and then click Help and.
Click Lenovo User Guide. Read before using your computer. The following sections provide critical safety and regulatory information for Lenovo computers and instructions on how to access electronic versions of the publications developed for your computer. Read first — regulatory information. Computer models equipped with wireless communications comply with the radio frequency and safety standards of any country or region in which it has been approved for wireless use.
In addition, if your product contains a telecom modem, it complies with the requirements for connection to the telephone network in your country. Be sure to read the Regulatory Notice for your country or region before using the wireless devices contained in your computer. Downloading publications. Electronic versions of your computer publications are available from the Lenovo Support Web site. Service and Support information.
The following information describes the technical support that is available for your product, during the warranty period or throughout the life of your product. Refer to the Lenovo Limited Warranty for a full explanation of Lenovo warranty terms. Online technical support. Telephone technical support. You can get help and information from the Customer Support Center by telephone.
Before contacting a Lenovo technical support representative, have the following information available: model and serial number, the exact wording of any error message, and a description of the problem. Your technical support representative might want to walk you through the problem while you are at your computer during the call. Worldwide Lenovo Support telephone list. Important: Telephone numbers are subject to change without notice. If the telephone number for your country or region is not listed, contact your Lenovo reseller or Lenovo marketing representative.
Country or region. Telephone number. Bolivia Calls made from within the Sao Paulo region: 11 Calls made from outside the Sao Paulo region: Brazilian Portuguese. Dial , then dial English and Bahasa Melayu. Depending on your operating system, the number of accessibility options available varies. Page Chapter 4. Security To set, change, or remove a power-on password, do the following: 1. Restart the computer.
When the logo screen is displayed, press F1 to start the ThinkPad Setup program. Page Supervisor Password Note: You might want to record your password and store it in a safe place. Otherwise, if you forget the password, you have to take your computer to a Lenovo reseller or a marketing representative to have the password canceled.
Page Hard Disk Passwords ThinkPad Setup program, you will be prompted to type your supervisor password to proceed. If you forget your supervisor password, Lenovo cannot reset your password. You must take your computer to a Lenovo reseller or a Lenovo marketing representative to have the system board replaced.
Proof of purchase is required, and a fee will be charged for parts and service. Page 62 If a user hard disk password has been set, but no master hard disk password has been, the user must enter the user hard disk password to access files and applications on the hard disk drive.
Page Hard Disk Security Lenovo cannot reset your passwords or recover data from the hard disk drive. You must take your computer to a Lenovo reseller or a marketing representative to have the hard disk drive replaced. Page 66 Swiping your finger over the fingerprint reader To swipe your finger over the fingerprint reader, do the following: 1. Place the top joint of your finger on the sensor.
Apply light pressure and swipe your finger toward you across the reader in one smooth motion. Do not lift your finger when you are swiping it. Page 67 If you forget your hard disk password, Lenovo cannot reset your password or recover data from the hard disk drive. You must take your computer to a Lenovo authorized servicer or a marketing representative to have the hard disk drive replaced.
Note: This item is displayed only if High security mode is enabled. These operations, however, only change the file location of the data; they do not delete the data itself. In other words, the data retrieval processing is disabled under an operating system such as Windows. Page 70 User Guide Page Chapter 5. Then, follow the instructions on the screen. The Rescue and Recovery program opens. Obtain them from Lenovo. Page Using The Advanced Startup Options To reset your computer to the factory default settings, do the following: 1.
Move your cursor to the top-right or bottom-right corner of the screen to display the charms. In the Remove everything and reinstall Windows section, click Get started. Then click Next to confirm the operation. Page 78 Note: Ensure that your computer is connected to ac power. Move your cursor to the top-right or bottom-right corner of the screen to display the charms, and click Search. Type recovery in the Search field and click Settings. Then click Create a recovery drive. Page Chapter 6.
Replacing Devices Replacing the battery pack Before you start, print these instructions. This system supports only batteries specially designed for this specific system and manufactured by Lenovo or an authorized builder. The system does not support unauthorized batteries or batteries designed for other systems. Page 80 Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.
Insert a new battery pack until it clicks into place. After the replacement, turn over the computer and connect the ac power adapter and all cables to the computer. Replacing the base cover assembly Before you start, print these instructions.
To replace the base cover assembly, do the following: 1. Install the battery pack. Turn over the computer and connect the ac power adapter and all cables. Note: If you remove the base cover assembly when your computer has the battery pack installed or is connected to ac power, there might be a risk of short circuits. Insert the new SIM card into the slot. Note: Ensure that you insert the SIM card all the way into the slot. Replacing the hard disk drive or solid-state drive Before you start, print these instructions.
Page 84 To replace the hard disk drive or solid-state drive, do the following: 1. Turn off the computer, then disconnect the ac power adapter and all cables from the computer. Remove the battery pack. Page 85 6. Detach the bracket from the hard disk drive or solid-state drive. Then attach the bracket to the new hard disk drive or solid-state drive.
Install the new hard disk drive or solid-state drive with bracket. Install the screw to secure the hard disk drive or solid-state drive. Chapter 6 Replacing devices Page Replacing A Memory Module 9. Install the base cover assembly and tighten the screws Replacing a memory module Before you start, print these instructions. Page 87 3. Loosen the screws that secure the base cover assembly. Then remove the base cover assembly as shown by the arrow 4.
Open the latches on both sides of the slot at the same time , and then remove the memory module Save the removed memory module for future use. Page Replacing The M. Place the notched end of the new memory module toward the contact edge side of the memory slot, and insert the memory module into the slot at an angle of about 20 degrees.
Pivot the memory module downward until it snaps into place. To avoid shock hazard, disconnect the cables before opening the cover of this slot. Attention: Before handling a card, touch a metal table or a grounded metal object. Page 90 4. If a tool is provided with the new card to help you disconnect cables, use the tool to disconnect the cables from the old card.
If no such a tool is provided, hold the cable connector with your fingers and gently disconnect each cable from the old card. Page 91 7. Align the notched edge of the new wireless LAN card with the key in the slot. Then carefully insert the card into the slot at an angle of about 20 degrees. Pivot the new wireless LAN card downward , and then install the screw to secure the card in place 9.
Installing or replacing the M. Page 93 4. If your computer already is installed with a wireless WAN card, remove it. Page 94 6. Carefully remove the wireless WAN card out of the slot. Align the notched edge of the new wireless WAN card with the key in the slot. Page Replacing The Ultrabay Device 9. Connect the antenna cables to the new wireless WAN card. Ensure that you connect the red cable to the main connector on the card, and the blue cable to the auxiliary connector on the card.
Page 96 4. Remove the screw that secures the Ultrabay device. Remove the Ultrabay device. Insert the new Ultrabay device into the bay. Page 97 7. Install the screw to secure the new Ultrabay device. Reinstall the base cover assembly.
Page Replacing The Backup Battery If the backup battery is incorrectly replaced, there is danger of an explosion. The backup battery contains a small amount of harmful substances. Page 99 5. Install the new backup battery and attach the connector 6. Install the base cover assembly and tighten the screws 7.
Page 4. To reveal the screw heads beneath the keyboard frame, use the flat end of the multi-tool to slide the keyboard forward by 2. Note: Do not press or hold the keys while sliding the keyboard frame, otherwise the keyboard frame cannot be moved. Page 7. Put the keyboard on the palm rest and detach the connectors. Then remove the keyboard. To install the new keyboard, do the following: 1.
Attach the connectors, and then turn over the keyboard. Page 2. Insert the keyboard into the keyboard bezel as shown. Ensure that the front edge of the keyboard is under the frame of the keyboard bezel. Ensure that the screw heads are exposed completely. Otherwise, reveal the screw heads by sliding the keyboard frame forward with the flat end of the keyboard multi-tool.
Tighten the screws with the cross end of the keyboard multi-tool to secure the keyboard in place. Slide the keyboard frame backward by 2. Page 6. Insert the flat end of the keyboard multi-tool into the gaps around the keys as shown to slide the keyboard frame backward.
Ensure that there is no gap between the keyboard frame and keyboard bezel. Note: Do not press and hold the keys while sliding the keyboard frame, otherwise the keyboard frame cannot be moved. Page User Guide Page Chapter 7. All you need is an Internet connection and a credit card. Eject button: Press the eject button to release the computer from the docking station.
Sliding adjuster: Use the sliding adjuster as a guide to align the docking station connector on your computer when you attach the docking station. Note: If you need to use an Ethernet connector or an external monitor connector when your computer is attached to a docking station, use the Ethernet connector or the external monitor connector on the docking station, instead of the one on the computer. USB 2. Key lock indicator: This indicator turns on when the system lock key is in the locked position.
Docking status indicator: This indicator turns on when your computer is docked. Align the top-left corner of the computer with the position mark of the docking station. Insert your computer into the docking station vertically until you hear a click.
The computer is attached to the docking station. Then turn the system lock key to the locked position 4. Press the eject button until the computer moves up. Then, grasp both sides of the computer to remove it. Security features The system lock key has two positions as shown in the drawing.
Page Chapter 8. To download the latest device drivers, do the following: 1. Select your product name to view all the device drivers for your computer. Select the device drivers you that you need, and follow the instructions on the screen.
Page Main Menu Note: Default values are in boldface. To change other configurations, press the Esc key to exit the submenu and return to the parent menu. When you complete the configuration, press F10 to save and exit. You also can select the Restart tab in the ThinkPad Setup menu, and restart your computer with one of the provided options. Page Table 4. Config menu items continued Menu item Value Submenu item Comments function is enabled with any power sources.
If you select Enabled, it enables USB 3. Config menu items continued Menu item Value Submenu item Comments connector on a docking station. Page The following table lists the Security menu items. Default values are in boldface. Attention: The default configurations are already optimized for you. Improper change of the configurations might cause unexpected results. Table 5. Page Table 5. Page Startup Menu Table 5.
Security menu items continued Menu item Value Submenu item Comments signature databases including certificate for Windows 8 operating system. Startup menu To change the startup settings of your computer, select the Startup tab from the ThinkPad Setup menu. Page Restart Menu Windows environment. Page Using System Management Using system management This topic is primarily intended for the network administrators.
Your computer is designed for manageability, so that you can redirect more resources to better meet your business objectives. This manageability, known as Total Cost of Ownership TCO , enables you to remotely operate client computers in the same way as you operate your own computer, such as turning on a client computer, formatting a hard disk drive, and installing a program.
Page Note: If a supervisor password has been set, you will be required to enter the supervisor password when you start the ThinkPad Setup program. Enabling or disabling the Wake on LAN feature When the Wake on LAN feature is enabled and the computer is connected to a LAN, the network administrator can start the computer remotely from a management console, using a remote network-management program.
Page Chapter 9. You might want to read the device driver information release notes prior to updating for compatibility or known issues. Getting the latest drivers from the Web site You can download and install updated device drivers from the Lenovo Web site by doing the following: 1.
Page Taking Care Of Your Computer For more information about how to use the System Update program, refer to the help information system of the program. Taking care of your computer Although your computer is designed to function reliably in normal work environments, you need to use common sense in handling it.
If you forget a supervisor or hard disk password, Lenovo will not reset it, and you might have to replace your system board, or hard disk drive or solid-state drive. Wipe the cover with the clean sponge. Wipe the surface again with a dry, soft, lint-free cloth. Wait for the surface to dry completely and remove any fibers from the cloth. Cleaning your computer keyboard To clean the computer keyboard, do the following: 1. Page Chapter
Step 1 Change BIOS Setting. Enter BIOS (Recommended way to enter BIOS - ideapad). Open the Exit menu (try to use Tab key or PgUp, PgDn, or arrow keys to. Solution · Attach the USB device to the system via any available USB port. · Press and hold the Power Button for few seconds to turn off the system completely. Symptom. After connecting an external hard drive to the USB port, the computer does not read the drive. The drive is not recognized by the operating.